Shipping an Excavator in a Container: Will It Fit, and How Does It Come Out?
Release time: 2026-11-05
At their listed shipping height, Caterpillar’s 3.5 t and 5.8 t mini excavators are 117 and 47 mm lower than the door of a 40ft high cube container; a 20 t excavator is not. That door is 2,340 mm wide (Hapag-Lloyd); the Cat 320 GC is 2,980 mm wide for transport, with a 2,380 mm track gauge. The extra width is in the undercarriage, so it usually ships on a flat rack or RoRo.
On a r/FreightBrokers thread (June 2024), a broker said that when he asks shippers how the receiver should unload their freight, some admit they never thought about it. A buyer on r/Alibaba (July 2025) who looked at a dozer from China said one of his problems was finding someone to put it back together once it arrived. This guide covers both ends: what goes into the container, and what you need ready when the doors open.
Container, flat rack or RoRo: the machine’s size decides
Start with the container’s numbers and the machine’s. The container figures below are from Hapag-Lloyd’s fleet pages, which note that dimensions vary slightly by container manufacturer.
| Container (Hapag-Lloyd figures) | Door opening, width by height | Inside length | Inside height | Max payload |
|---|---|---|---|---|
| 20ft standard | 2,340 by 2,292 mm | 5,900 mm | 2,395 mm | 28,130 kg |
| 40ft high cube | 2,340 by 2,597 mm | 12,032 mm | 2,700 mm | 28,600 kg |
Sources: Hapag-Lloyd 20′ Standard and 40′ Standard High Cube, accessed 26 October 2026.
Now the machines. Caterpillar publishes transport dimensions on its product pages, so we use three Cat models as reference points. Check the spec sheet of the exact model you are buying in the same way.
| Machine (Caterpillar figures) | Operating weight | Width | Shipping height | Lower than the 20ft door? | Lower than the 40ft high cube door? |
|---|---|---|---|---|---|
| Cat 303 CR mini excavator | 3,545 kg | 1,550 mm (track width) | 2,480 mm | No: 188 mm too tall | Yes, by 117 mm |
| Cat 305 CR mini excavator | 5,754 kg | 1,980 mm (track width) | 2,550 mm | No: 258 mm too tall | Yes, by 47 mm |
| Cat 320 GC excavator | 20,400 kg | 2,980 mm (transport width) | 2,960 mm (top of cab) | No | No: 640 mm too wide, 363 mm too tall |
Sources: Caterpillar Australia product pages for the 303 CR, 305 CR and 320 GC, accessed 26 October 2026. The yes and no columns are our comparison of those figures with the door sizes above.
Three things follow:
- These two Cat minis clear a 40ft high cube door on paper, but not a 20ft door. The limit on a 20ft standard is door height: both are above its 2,292 mm opening at their listed shipping height. Check your own model’s shipping height against that figure. The 305 CR’s 47 mm is a static margin on paper; it leaves little or no room for bedding timber under the tracks or the angle of a loading ramp, so ask the seller to confirm the loading height before booking.
- A 20 t machine does not fit through any standard container door as delivered. It is wider and taller than the opening, and on the 320 GC the extra width is in the undercarriage: its track gauge alone is 2,380 mm, wider than the 2,340 mm door. Taking off the boom, arm or bucket does not change that, so ask the seller exactly how the width will be reduced, or plan for a flat rack or RoRo.
- Length is rarely the problem in a 40ft box. The 320 GC’s shipping length of 9,530 mm is shorter than the 12,032 mm inside length; weight is within the payload too. Width and height are what decide.
A flat rack has a floor and end walls but no side walls or roof, as the IMO/ILO/UNECE CTU Code describes it, so the door limit disappears. Its lashing brackets are also stronger: the Code gives at least 30 kN, and often 50 kN, against 10 kN for the floor rings of a general purpose box. If the machine is wider than the rack, get the carrier’s written acceptance of the load before it leaves the yard. On a RoRo vessel the machine is driven aboard on its own tracks or wheels. For what each option costs on the China to USA route, see our excavator shipping cost and timeline guide.
Taking a 20 t machine apart for shipping: two of our orders
On 26 December 2025 we loaded a Komatsu PC200, ordered by a client in Asia with a hydraulic breaker and a quick coupler, into a 40HQ container (our news post from that day). The post does not list what was taken off to get it through the door.

The 40HQ before loading, 26 December 2025.

The same PC200 with its quick coupler and hydraulic hoses on the ground, ready to be packed.
For a Hyundai 220LC-9S we prepared for a buyer in Guyana in December 2025, the boom and arm were taken off and strapped onto the upper structure, with the bucket strapped beside them (our post on that order).

The Hyundai 220LC-9S for Guyana with boom, arm and bucket strapped down, December 2025.
Whatever the seller takes off, get it in writing before the machine is loaded. Ask for:
- A list of every part removed (attachments, bucket, arm, boom or anything else) and where each one will travel.
- A tag or paint mark on each loose part and each hose end, matched to the list.
- Photos of each removed part and each capped hose end before packing.
- Who will refit the parts at the other end, and what tools or lifting gear that will need.
Securing it inside: floor load, lashing points and timber
A container floor is built for weight spread across it, not a heavy machine sitting on two narrow tracks. The CTU Code (IMO circular MSC.1/Circ.1497, 2014) says container floors are designed for the total payload “homogeneously distributed,” that floors covered by the CSC need only withstand an axle load of 5,460 kg, and that a concentrated load may need to rest on strong timber or steel beams, planned with the container operator, to carry its weight to the corner posts.
It also gives the strength of the lashing points: bottom anchor points in a general purpose container are rated for a maximum securing load of at least 10 kN, and 20 kN in many newer units. A 20,400 kg machine weighs about 200 kN (our arithmetic). Sea motion pushes a share of that weight sideways and lengthways, and each ring is rated for 10 or 20 kN, which is why a heavy machine is blocked with timber against the floor and walls and lashed at many points.
The timber matters at the border, too. Canada’s directive D-98-08 (effective 1 April 2026) requires all wood packaging, including dunnage and bracing, to bear the IPPC mark of the international ISPM 15 standard. It warns that pieces cut to fit the cargo may lose that mark and then may not be accepted, unless a phytosanitary certificate covers them. Blocking cut to the shape of a track frame is exactly that kind of wood. Ask whether the timber is marked, and photograph the marks. The directive’s appendix also allows the mark to be applied again on treated dunnage after cutting, in a visible place, provided the shipper is authorized under ISPM 15; ask the seller whether its packer can do that.
Before the doors close, ask for photos of:
- the machine’s position in the box, with timber bedding under the tracks
- every lashing, at both ends
- the blocking timber, with its IPPC mark visible
- the seal number on the closed doors
Fuel and the dangerous-goods question
In a container, a machine with fuel in its tank and an engine that can run is regulated cargo at sea; RoRo carriers have their own rules for fuel, so ask them. Swire Shipping’s customer guidance explains that under special provision 363 of the IMDG Code, machinery can be shipped as non-hazardous when its liquid fuel tank has been drained and the engine cannot run for lack of fuel, with a signed letter of indemnity from the shipper or supplier confirming it (Swire Shipping knowledge base, accessed 26 October 2026). The rules differ by carrier, so ask the seller which carrier is booked and what that carrier requires, including for the batteries.
There is a practical consequence at the other end. A machine shipped with a drained tank cannot be driven out of the container until it has fuel. Put fuel on your unloading list.
Cleaning before the doors close
Soil on a used machine can stop it at the border. Canada’s directive D-95-26 prohibits the import of items contaminated with soil, and names machinery, vehicles and equipment. Non-compliant goods can be refused entry, ordered removed or disposed of, and the person in charge of them pays the costs. Other countries apply their own rules; our guide to import requirements by destination lists them with the official sources.
Cleaning is one of the steps we list in our own preparation. In the South American PC200 order described in our December 2025 post, the machine was serviced and cleaned before the vessel was booked. Ask for photos of the undercarriage, track frames and radiator area after washing, taken on the day of loading.
Getting it out at the other end
The CTU Code has a chapter on unpacking, and three points from it apply directly to a machine:
- Cargo may have shifted at sea and can press against the doors, so open them with care. The Code encourages a safety strap secured around the door’s inner locking rods, so the door opened first cannot swing free.
- When lashings and blocking are removed, make sure the machine cannot move as each one is released.
- Document any damage found during unloading and notify the carrier, the container operator or the shipper as appropriate.
Before the container is released to you, settle the rest:
| Question | Why it matters |
|---|---|
| Where will the container be unpacked: at the terminal, a depot or your yard? | That decides who supplies the ramp, crane or second machine, and how long you can keep the box. |
| Can the machine be driven out, or must it be pulled out? | It needs fuel and a charged, connected battery to drive out under its own power. |
| What lifts the loose parts? | A boom, arm or breaker taken off in China has to be lifted out and refitted. |
| Who refits the parts and reconnects the hoses? | Line up a mechanic before arrival, with the parts list and photos from loading. |
| Who checks for transit damage before the carrier’s people leave? | Damage claims need it recorded at unpacking. |
| Who cleans the container and disposes of the timber? | The CTU Code makes the consignee responsible for returning the container clean unless agreed otherwise, and, where wood quarantine rules apply, timber without an IPPC mark is disposed of under national or local plant protection rules. |
How many fit in a 20GP or a 40HQ
On paper, two of either Cat mini fit in a 40ft high cube, and none goes through a 20ft door. The table below is our arithmetic from Caterpillar’s listed shipping lengths (long stick) and weights, against Hapag-Lloyd’s 40ft high cube inside length of 12,032 mm, inside width of 2,350 mm and payload of 28,600 kg. It leaves out the space needed for lashing and blocking, and Caterpillar notes that shipping length depends on where the blade sits during shipment.
| Machine | Shipping length | Two end to end | Three end to end | Weight of two | Side by side? |
|---|---|---|---|---|---|
| Cat 303 CR | 4,560 mm | 9,120 mm: fits 12,032 mm | 13,680 mm: too long | 7,090 kg | No: 2 x 1,550 mm is wider than 2,350 mm |
| Cat 305 CR | 5,340 mm | 10,680 mm: fits | 16,020 mm: too long | 11,508 kg | No: 2 x 1,980 mm |
| Cat 320 GC | 9,530 mm | Not through the door: track gauge 2,380 mm is wider than the 2,340 mm door | n/a | n/a | n/a: plan for a flat rack or RoRo |
Real loads depend on the exact model, how much is taken off, and the timber and lashing space. We have not published per-container counts from our own loads yet. Before you pay for a second machine in the same box, ask the seller for a loading plan: a drawing of where each machine sits, its weight, the total against the payload, and what was removed from each.
What to agree with the seller before the container is booked
| Item | What to get in writing |
|---|---|
| Shipping method | Container, flat rack or RoRo, and why, for your machine’s dimensions |
| Parts removed | The list, the tags, the photos |
| Securing | Bedding, lashing and blocking photos; timber with IPPC marks |
| Fuel | Tank drained or not, and the carrier’s requirement (SP363 letter, batteries) |
| Cleaning | Undercarriage photos on loading day |
| Documents | Packing list naming every loose part; seal number |
| Unloading | Where it will be unpacked and who refits the parts |
For machines we have in stock now, see our used excavators.
Frequently asked questions
Can a 20 ton excavator fit in a 40ft container? Not as delivered. Caterpillar lists the 320 GC at 2,980 mm wide and 2,960 mm to the top of the cab, while a 40ft high cube door is 2,340 mm wide and 2,597 mm high in Hapag-Lloyd’s specification. The extra width is in the undercarriage, so removing the boom and arm is not enough; it usually ships on a flat rack or RoRo unless the seller can show how the width is reduced.
Can a mini excavator be shipped in a 20ft container? Caterpillar’s 303 CR and 305 CR cannot go through the door: their shipping heights of 2,480 and 2,550 mm are above the 2,292 mm door of a 20ft standard. Both are lower than the 2,597 mm door of a 40ft high cube, the 305 CR by only 47 mm. Check your own model’s shipping height against those figures.
Does the fuel have to be drained to ship an excavator in a container? To ship machinery as non-hazardous under IMDG special provision 363, carriers such as Swire Shipping require the fuel tank to be drained so the engine cannot run, with a signed letter of indemnity. Ask the booked carrier for its own requirement.
Who unloads an excavator from a container at the destination? It depends on where the container is unpacked. Agree before arrival who supplies fuel, a ramp or lifting equipment, and a mechanic to refit any parts removed for shipping.
Last checked against the linked sources on 4 November 2026 · Prepared by HCQ Machinery’s export team. This article was drafted with AI assistance. The sources checked were the container and machine dimensions, the CTU Code, the carrier guidance and the CFIA directives. The photographs were first published in HCQ’s news posts linked above, in December 2025.

